You are here

Tips - Error-Free Connections with Named Wires | Cypress Semiconductor

Tips - Error-Free Connections with Named Wires

In a recent blog I talked about wiring tips for faster design. One of the risks with being a wire-drawing wizard, though, is that it can lead to a bit of a messy schematic. It is tempting to just drop in your components anywhere on the page and hook them up. If you ever look at an old design and wonder what you were thinking about at the time then I recommend naming your wires.

PSoC Creator resolves wires with the same name into a single signal path when it builds a project and so two (or more) wires with the same name are functionally equivalent to a single wire with fourteen elbows meandering around a cluster of components.

Here is a design I made recently that uses a PWM with two outputs to drive a reflectance sensor. The first output (pwm1) turns the LED on briefly and the second (pwm2) triggers the D flip-flop to read the state of the pin a little while later. The reflectiveness of the surface determines how long the transistor takes to decay and so the output of the flip-flop is always a snapshot of the state of the sensor. In firmware, I read the status register and can make decisions based on the surface my board is lying on.

Driving a Reflectance Sensor

The problem is that I have five of these sensors and I wanted to drive them all from the same PWM and read them from one status register. I made copies of the pin and flip-flop and started wiring but it took quite a while. I kept making mistakes because I could not remember which wire should go where and I would inadvertently connect two wires that were driven by different signals. I managed to get three sensors working.

Driving Three Reflectance Sensors

I was daunted by the prospect of more wiring and I was running out of room on the page! How would I  ever maintain this project? So, in the end, I gave up and took the extra 30 seconds to just name the wires coming from the PWM and those going to the status register. You just right-click on the wire and choose "Edit Name and Width" to do this.

Wire Naming Dialog

I then tidied up the design in no time. As you can see, naming the wires let me break the whole design into three pieces; the PWM, the pins and flip-flops, and the status register. I managed this without ever making a bad connection and it is much easier to see the connectivity when there are not wires running around and crossing each other.

PWM with Named Wires

Reflectance Sensor Pins

Status Register holds Sensor State

 

Taking a few seconds to name wires can save you a lot of time drawing your schematics. Not only can you make designs (that work) quickly but you can do so in a way that is far easier for other engineers to understand. In a future blog I will expand on that idea with some more tips on making schematics with lots of repeated content, like all these pins and flip-flops, even easier to read and maintain.

Blog: 

본 사이트의 모든 컨텐츠와 자료는 "있는 그대로" 제공됩니다. CYPRESS SEMICONDUCTOR와 해당 공급자는 그 목적에 관계 없이 이러한 자료의 적합성에 대한 표현을 하지 않으며 상업성, 특정 목적에의 적합성, 권리 및 제3자 지적 재산권의 비침해에 대한 모든 묵시적 보증과 조건을 포함하여(이에 제한되지 않음) 이러한 자료와 관련한 모든 보증과 조건을 부인합니다. CYPRESS SEMICONDUCTOR에서는 명시적 또는 묵시적으로 금반언이나 여타의 다른 방법으로 라이센스를 부여하지 않습니다. 이 사이트의 정보를 사용하려면 제3자의 라이센스 또는 CYPRESS SEMICONDUCTOR에서 제공하는 라이센스가 필요할 수 있습니다.

이 사이트의 컨텐츠에는 특정 사용 지침이나 제한이 포함되거나 그러한 제한이 적용될 수 있습니다. 모든 게시물과 이 사이트 컨텐츠 사용에는 사이트 약관이 적용됩니다. 이 컨텐츠를 사용하는 제3자는 제한 또는 지침을 따르고 이 사이트의 약관을 준수할 것이라는 데 동의합니다. Cypress Semiconductor와 그 공급자는 컨텐츠와 자료, 그 제품, 프로그램 및 서비스를 언제든 수정, 삭제, 개조, 개선, 향상 및 기타 변경하거나 예고 없이 컨텐츠, 제품, 프로그램 또는 서비스를 이동 또는 중단할 수 있는 권리를 보유합니다.