FM4 S6E2H-Series Motor Control Arm® Cortex®-M4 Microcontroller (MCU) Family | Cypress Semiconductor
FM4 S6E2H-Series Motor Control Arm® Cortex®-M4 Microcontroller (MCU) Family
S6E2H-Series are highly integrated 32-bit microcontrollers with high performance and competitive cost. This series is based on the Arm Cortex-M4F processor with on-chip flash memory and SRAM. The portfolio includes serial communication interfaces (UART, CSIO (SPI), I2C, LIN), 2 CAN bus interfaces and advanced control peripherals such as motor control timers, A/D converters and a Quadrature Position/Revolution Counter.
S6E2H-Series Highlights
High-Performance MCU Subsystem
- 540 CoreMark®, 160-MHz Arm® Cortex®-M4 CPU
- 188-µA/MHz active current with 2.7-V to 5.5-V operating voltage
- Ultra-low power 1.3-µA real-time clock (RTC) operating current
- Up to 512KB flash and 64KB SRAM with a 16KB flash accelerator
- Error-Correcting Code (ECC) support, hardware Watchdog timer (WDT), low-voltage detect, and clock supervisor blocks for safety-critical applications
디지털 서브시스템
- 3x Multi-Function Timers (MFT)
- 9x Programmable Pulse Generators (PPG)
- 8x Base Timers, 3x Quadrature Position/Revolution Counters (QPRC)
- 1x Dual Timer, Cyclical Redundancy Check (CRC), and Watch Counter
- 8x channels of Multi-Function Serial (MFS) interfaces configurable as SPI, UART, I2C, or LIN
- 2x CAN, SD Card and External Bus Interface
Analog Subsystem
- 3x 12-bit, 2-Msps ADC with a 24-channel multiplexer input
S6E2HG-Series Block Diagram
1 Watchdog Timer |
2 Cyclical Redundancy Check |
3 Controller Area Network |
4 Memory Protection Unit |
5 Direct Memory Access |
6 Descriptor System Transfer Controller |
Function Differences between each S6E2H-Series by part
Series | S6E2HG | S6E2HE | S6E2H4 | S6E2H1 |
CAN | 2 ch. (Max) | - | 2 ch. (Max) | - |
SD Card Interface | 1 unit | 1 unit | - | - |
- Watch the Introduction to the FM4 Portfolio video
- Download the S6E2H-Series Datasheet
- Purchase the FM4 Starter Kit (FM4-120L-S6E2HG) to evaluate the S6E2H-Series and start development
- Download the FM4 Peripheral Driver Library Software
- Start your first FM4 designs
- Join the Cypress Developer Community
FM4 S6E2H-Series Datasheets
|
FM4 S6E2H-Series Flash Specifications
|
FM4 S6E2H-Series Technical Reference Manual
|
애플리케이션 설명
|
Peripheral Driver Library
FM MCU Peripheral Driver Library (PDL)
The FM MCU Peripheral Driver Library (PDL) simplifies software development for the FM0+, FM3, and FM4 MCU families. The PDL reduces the need to understand register usage and bit structures, thus easing software development for the extensive set of peripherals in the FM families. You configure the library for the particular device, and then use API calls to initialize and use a peripheral. Using the PDL makes it easier to port code from one family to the other, because the same code supports all FM families.
Support Tools
Vendor | Link | Comments |
IAR Systems | https://www.iar.com/iar-embedded-workbench/#!?architecture=ARM | IAR Embedded Workbench for Arm 7.50.2 or later |
Arm Keil | https://www.keil.com/download/product/ | Keil Embedded Development Tools for Arm 5.17 or later |
GCC Arm Embedded | https://launchpad.net/gcc-arm-embedded | GCC Arm Embedded 4.9-2015-q1-update or later |
iSystem | https://www.isystem.com/download/winidea/release-policy | iSYSTEM winIDEA 9.12 or later |
도구
Click on the link below to download the tool
Product | Description |
Pin and Code Wizard | Tool that helps set the IO ports for Cypress's 32-bit Arm Cortex FM MCUs |
Serial Port Viewer Tool | Tool that is used to monitor all available com ports and provides a terminal emulator |
CMSIS-DAP USB Drivers | CMSIS-DAP is the interface firmware for a Debug Unit that connects the Debug Port to USB. Debuggers, which execute on a host computer, connect via USB to the Debug Unit and to the Device that runs the application software |
FLASH Programmer | Tool that converts RS232C data to readable data on your PC |
USB Wizard | Tools that supports editing USB descriptors and templates |
FM4 S6E2H-Series Starter Kit
These kits will help you get started with FM4 MCU development.
|
The Sample Programs ("Programs") are offered for use in developing systems for Cypress microcontrollers.
The Programs will be useful in the following situations:
- I need a simple sample program, as I am going to develop software. The sequence of resource access, among others, can be confirmed using these Programs.
- I would like to examine, before development, whether each resource will operate as expected.
The Programs support several specifications, even for the operation of one resource. - If resources do not operate properly on my system, I would like software for which confirmation of operation has been completed. Cypress has confirmed the actual operation of the Programs on each of its microcontrollers, so you will be able to compare your program with the Program.
For the FM portfolios, code examples are provided with the Peripheral Driver Library (PDL). Download and install the PDL, and look in the examples folder.